+44 (0)117 244 3000

OUR PROJECTS

Electronic Products for a broad range of sectors

Metryx

Metryx mass metrology on product wafer measurement, low cost of ownership, high RoI and atomic level repeatability…

At the heart of Metryx business is the Metryx mentor range, which is an in-line process monitoring solution that rapidly identifies production wafer trends and excursions. Monitoring the mass change for any process step is an effective in-line check, revealing the true wafer mean, while flagging the bad wafers.

Close Air Solutions Logo

Key features of Metryx Mass Metrology tools include;

  • On-Product Measurement
  • Non-invasive
  • Atomic level accuracy
  • Applicable to all process modules – deposition, etch and CMP, on metals and dielectrics
  • High throughout in-line solution
  • Self-contained corroboration of metrology result
  • No monitor wafers or test sites required
  • Low CoO
  • User friendly software with recipe editing and configuration user security.

In 2002, Metryx started to sell its unique mass metrology technology to semiconductor manufacturers. Today that technology is in volume production all over the world helping Fabs to ramp production wafers quicker than at any other time before. Their system is helping Fabs running at capacity to make sure their process is running at an optimal level.

Mass metrology provides a unique measurement of the mass change resulting from any process step. Mass change is a fundamental measurement of the change induced on a wafer by a process step.

Metryx Distro Unit
Metryx Distro Unit

Metryx first approached Cubik Innovation in 2014, with the need for a design alteration to an existing product. The block of design work included a prototype run of the PCBs used in the product. The success of the design alteration block of work that was carried out, has meant that Cubik have undertaken many different projects for Metryx including the up issue and ongoing batch build of a set of 13 different PCBs.

AC Distribution Unit manufactured by Cubik

 

Metryx Distro Unit

During the beginning of 2016 Metryx approached Cubik with a new block of work that they hoped Cubik could assist with. This was the procurement, assembly and test of a set of Electrical and Mechanical products, an example of these is shown above. These products had been designed by Metryx and up until this point had been assembled in small quantities either in house or with another supplier. Metryx was looking for a new partner to help with larger assembly batches.

Cubik were already supplying their PCBs and were well placed to provide the necessary skills needed for the assembly project. Cubik has to date delivered over 60 complete assemblies and hopes this is an ongoing partnership between Metryx and Cubik.

Metryx Main

High Res Main

 

Metryx Main Stacked

Stacked Module

 

CONTACT US TODAY TO DISCUSS YOUR REQUIREMENTS

HiETA

Adrian Schmieder of HiETA commented: “Cubik’s quick turn-around of a functioning PCB has sped the delivery of the project and enabled me to focus on areas of the project in which HiETA has expertise.  The project is a great success and produced valuable information even from its first use.  I am very impressed with the support Cubik provided me throughout the project, from initial concept through to PCB delivery.  I will not hesitate to engage with them again as future PCB projects arise.”

Inductosense

Speaking about the collaboration between Inductosense and Cubik Innovation, Founder and CTO Dr Chenghuan Zhong (Bamboo) stated: "It was great working with the knowledgeable and experienced team at Cubik Innovation. They always provide full support as well as useful and thoughtful advice to us, helping us find solutions for really difficult problems."

Aquabar

Geoff Jones, Aquabar Inventor: "It was a pleasure to work with Cubik on our project. Paul and Sam understood the concept at one meeting, and produced a solution filling the brief within two weeks which has enabled us to find a potential partner. We will certainly use Cubik for our production units later in the year, Many thanks."

Plymouth University

Paul Davey, Associate Professor (SL) Plymouth University: "If you need a prototype developed to a high standard and on time you would be hard pushed to find someone better. They have highly trained, experienced engineers who get the job done."

Clean Energy Prospector Ltd

Damon Rand, Head Product Design: "Paul and the team have really helped us speed up the turnaround on our prototypes and assure the manufacturability of our designs. If you’re designing electronics in the South-West, then Cubik is a great choice for short-run manufacturing."

Cubik Innovation Ltd
Verona House
Filwood Road
Fishponds
Bristol BS16 3RY
United Kingdom
T: +44 (0)117 244 3000

Electronic design Bristol, Prototype, Product design, PCB design, PCB assembly, PCBA, Electronic design UK, Custom Electronics, Analogue, digital and mixed signal design - Printed circuit board design - Embedded microprocessor systems - Prototyping and test - Mechanical design - Project planning - Production support – Batch Production - Production test and ATE – Small Batch Manufacturing

© Copyright 2012-2018 Cubik Innovation Ltd.
Company No. 8150022
VAT No. 139 8630 80.